1 5

HK ADVANCE

2PCS Car Spring Shock Absorber Buffer Pad – Shock Absorption Rubber Ring

2PCS Car Spring Shock Absorber Buffer Pad – Shock Absorption Rubber Ring

$46.00 AUD
$66.00 AUD $46.00 AUD
Sale Sold out
Size
(Install one for each wheel.) Therefore, the minimum order quantity is 2 pieces. For one vehicle, 4 pieces should be ordered. Please find the size that suits your car.


I. Product Functions


  1. If the spring has become weak (the vehicle body is pressed down very low when carrying a slightly heavier load), it is recommended to install the buffer rubber! It can assist the spring, relatively raise the vehicle body, and improve the load-bearing capacity.
  2. If you often drive on rough roads (the instantaneous pressure during bumps is likely to damage the suspension system), it is recommended to install the buffer rubber! It can enhance the shock absorption effect, absorb the instantaneous pressure, and protect the shock absorber and the suspension system.
  3. If you often carry heavy loads (the shock absorber and the suspension system are more prone to aging), it is recommended to install the buffer rubber! Through buffering and shock absorption, it protects the shock absorber and the suspension system and extends the service life of the shock absorption system.
  4. If you think the current shock absorption effect is not good (there is no comfort, which will lead to driving fatigue and no driving pleasure), it is recommended to install the buffer rubber! It can improve the shock absorption effect, enhance the driving comfort, and enable you to enjoy the pleasure of driving.


This is a transparent shock absorber buffer.


II. Product Features


  1. Effectively solve the problem of the weak shock absorber spring and restore the performance of the shock absorber.
  2. Adopt the buffering principle, significantly improve the shock absorption performance, and provide the comfort similar to that of a Mercedes-Benz.
  3. Protect the shock absorber and the suspension system and prevent the oil seal of the shock absorber core from leaking oil.
  4. The test results show that it can extend the service life of the shock absorber by more than 2 times.
  5. Reduce the noise during driving.
  6. Raise the vehicle body by 3-5 cm (about 1-2 cm for some new vehicles), restore the original height of the vehicle body, and improve the stability when passing over speed bumps.
  7. Shorten the braking distance and improve safety.
  8. Relieve the fatigue feeling after long-distance driving.
  9. Easy to install without loosening any screws of the vehicle.


III. Product Dimensions
As shown in the figure.


IV. Installation Method


  1. Use a jack to lift the wheel off the ground (just like when changing a tire). In most cases, there is no need to remove the wheel.
  2. Wipe the shock absorber spring clean with clean water (wipe it several times) to ensure that the spring is clean and free of gravel, as gravel will reduce the service life of the shock absorber.
  3. Apply soapy water (soaked soap) to the shock absorber spring, and also apply soapy water to the groove of the strong buffer. Wash your hands, and then install the strong buffer onto the spring (install the upper groove first, and then the lower groove. You can also install half of the upper and lower grooves first, and then rotate to install the remaining parts until the entire spring is located in the groove).
  4. Finally, after installation, hold the buffer with both hands, turn the notch towards the middle of the inner side, and use the middle fingers of both hands to measure the distance between the buffer and the fender. It is best if the middle fingers of both hands can be inserted at the same time. Touch it with your hands to confirm that the spring is all in the groove, and then you can lower the vehicle body.
V. Precautions


  1. Try to install the strong buffer in the middle part of the shock absorber spring.
  2. Do not use tools to pry during installation: The distance between the shock absorber springs is a matter that needs attention when installing the shock absorber buffer. What consumers need to know is that "the distance between the shock absorber springs should be equal to the height of the shock absorber buffer." Generally speaking, it is best to install the automobile spring shock absorber buffer in the middle part of the spring. Try not to use tools to pry when installing the shock absorber buffer to avoid damaging the buffer. Of course, before performing the above steps, first use a jack to support the vehicle body and wash the spring with water. After installation, rotate the automobile shock absorber buffer left and right several times to check whether the spring is fully installed in the spring groove; whether the outer edge of the buffer rubs against the fender; and whether the buffer overlaps.
View full details